View 7596A_373611.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

Variable Capacitance Accelerometer
Model 7596A
* * * * * Economical and Rugged 2 to 100 g Full Scale DC Response Gas Damped Sensor Mechanical Over-range Stops
Actual size
ENDEVCO
MODEL 7596A
DESCRIPTION The ENDEVCO(R) Model 7596A VALULINETM accelerometer family is a low cost solution to low-level, low frequency measurements. Applications include laboratory measurements, ground transportation studies and measurements where the accelerometer will be subjected to high shock levels (up to 10 000 gs, see specifications). The 7596A is ideal for modal studies on large structures. Gas damping and internal overange stops enable the anisotropically etched silicon microsensors to withstand high shocks and acceleration loads. The use of gas damping, in the sensor, results in very small-induced changes of frequency response. The patented sensor design ensures immediate stability making the unit ready to take accurate DC or dynamic data within one millisecond! The 7596A can operate from 8.5Vdc to 30Vdc and provide a high level, low impedance output. The output is high enough to drive most laboratory instruments, tape recorders and data acquisition systems without amplification or signal conditioning. The output can be fed into either a differential or single-ended amplifier or standard bridge electronics with 10Vdc excitation.
ENDEVCO Model 136 Three-Channel System, Model 4430A or OASIS Computer-Controlled System are recommended signal conditioners.
SPECIFICATIONS
PERFORMANCE CHARACTERISTICS: All values are typical at +75F (+24C) and 15 Vdc excitation unless otherwise stated. Calibration data, traceable to the National Institute of Standards, (NIST), is supplied. Units g pk mV/g Hz Hz % FSO Typ % FSO (Max) % Typ mV Max %/F %/C 7596-2 2 1000 100 0 to 15 1300 0.20 0.50 1 200 3.0 +0.04 +0.08 -10 10 200 20 0 to 500 3000 0.20 0.50 1 200 0.7 +0.04 +0.08 -30 30 66 8 0 to 800 5500 0.20 0.50 1 200 0.7 +0.04 +0.08 -50 50 40 4 0 to 1000 5500 0.2 0.5 1 200 0.6 +0.04 +0.08 -100 100 20 2 0 to 1000 6000 1 2 1 200 0.6 +0.04 +0.08
RANGE SENSITIVITY (at 100 Hz) [1] [2] FREQUENCY RESPONSE ( 5%) MOUNTED RESONANCE FREQUENCY NON-LINEARITY AND HYSTERESIS [3] TRANSVERSE SENSITIVITY [4] ZERO MEASURAND OUTPUT [2] DAMPING RATIO DAMPING RATIO CHANGE From -65F to +250F ( -55C to +121C)
APPLIES TO CALIFORNIA FACILITY
ENDEVCO
Variable Capacitance Accelerometer
SPECIFICATIONS--continued
PERFORMANCE CHARACTERISTICS--continued Units 7596-2 -10 THERMAL ZERO SHIFT From 32F to 122F (0C to 50C) % FSO Max 2.0 2.0 From -13F to +167F (-25C to +75C) % FSO Max 4.0 4.0 From -65F to +250F (-54C to +121C) % FSO Max 6.0 6.0 THERMAL SENSITIVITY SHIFT From 32F to 122F (0C to +50C) % Max 2.0 2.0 From -13F to +167F (-25C to +75C) % Max 4.0 4.0 From -65F to +250F (-54C to +121C) % Max 6.0 6.0 THERMAL TRANSIENT ERROR Equiv. g/F < 0.0006 < 0.0006 PER ISA RP 37.2 Equiv. g/C < 0.001 < 0.001 OVERRANGE (Determined by Electrical clipping or Mechanical stops, whichever is smaller.) Electrical clipping g -3.5/+3.8 -18/+19 Mechanical stops, typical g 4 30 Recovery Time s < 10 < 10 THRESHOLD (RESOLUTION) [5] Equiv. g's 0.0005 0.0025 BASE STRAIN SENSITIVITY, MAX [6] Equiv. g's 0.01 0.01 MAGNETIC SUSCEPTIBILITY [7] Equiv. g's <1 <1 WARM-UP TIME (to within 1%) ms 10 10 ELECTRICAL EXCITATION [2] CURRENT DRAIN [8] OUTPUT IMPEDANCE/LOAD RESIDUAL NOISE ISOLATION PHYSICAL CASE, MATERIAL/BASE ELECTRICAL, CONNECTIONS MOUNTING/TORQUE WEIGHT ENVIRONMENTAL ACCELERATION LIMITS (in any direction) Static Sinusoidal/Random Vibration Shock (half-sine pulse) Zero Shift TEMPERATURE Operating Storage HUMIDITY/ALTITUDE ESD SENSITIVITY -30 2.0 4.0 6.0 2.0 4.0 6.0 < 0.0006 < 0.001 -53/+57 90 < 10 0.008 0.01 <1 10 -50 2.0 4.0 6.0 2.0 4.0 6.0 < 0.0006 <0.001 -87/+95 200 < 10 0.0012 0.01 <1 10 -100 2.0 4.0 6.0 2.0 6.0 6.0 < 0.0006 < 0.001 -175/+190 200 < 10 0.025 0.01 < 0.1 10
MODEL 7596A
8.5 to 30 Vdc, 32 Vdc maximum without damage; excitation voltage can be applied to any lead without damage 4.5 mA Typ, 8 mA Max 50 ohms max/10K ohms resistance minimum, 0.1 F capacitance maximum 100 V rms typ, 0.5 to 100 Hz. 500 V rms typ, 0.5 Hz to 10 KHz 100 M
Anodized Aluminum Alloy 28 AWG silver plated alloy 135, PFA340 Teflon(R) insulated conductors, spiral shield (SPC), HyperFLEXTM jacket with TFE non-fray, end grip 30 3 inches (760 76mm) long. Two 4-40 x 3/8 6 lbf-in (0.7 Nm) 10 grams (cable weighs 9 grams/meter)
20 000 g 100 g pk, 20 - 2000 Hz/40 g rms, 20 - 2000 Hz 5000 g, 150 sec or longer for the -2 and -10; 10 000 g, 80 sec or longer for the -30 and -100 0.1% FSO typical at 5000 g -65F to +250F (-55C to +121C) -100F to +300F (-73C to +150C) Unaffected. Unit is epoxy sealed. Hybrid and sensor are hermetically sealed/unaffected. Unit meets Class 3 requirements of MIL-STD-883
CALIBRATION DATA SUPPLIED (noted on shipping box) SENSITIVITY (at 5 Hz and 1 g pk, for 2 g range) (at 100 Hz and 10 g pk, all other ranges) mV/g with 15 Vdc excitation FREQUENCY RESPONSE 1 to 100 Hz for 7596A-2, 20 to 10000 Hz for all other ranges ZERO MEASURAND OUTPUT mV MAXIMUM TRANSVERSE SENSITIVITY % of sensitivity ACCESSORIES (included) EHW265 (2) SIZE 4, FLAT WASHERS EH409 (2) 4-40 X 3/8 INCH CAP SCREWS EHM464 (1) HEX WRENCH OPTIONAL ACCESSORIES 24328 4 CONDUCTOR SHIELDED CABLE 7990 TRIAXIAL MOUNTING BLOCK NOTES 1. Reference frequency is 20 Hz on the 2 g range. 2. Over the excitation range 8.5 to 30 Vdc. Sensitivity changes +0.1%/V typical and zero measurand output changes -0.5 mV/V typical. 3. Full scale output (FSO) is nominally 4 volts. 4. 1% is typical. 1% maximum available on special order. 5. THRESHOLD = MAX. RESIDUAL NOISE; 0.5 TO 100 Hz SENSITIVITY 6. Per ISA 37.2 at 250 Microstrain. 7. At 100 Gauss, 60 Hz. 8. Current drain increases slightly with increasing excitation; typical change is +.06 mA per volt from 8.5 to 30 Vdc. 9. Maintain high levels of precision and accuracy using Endevco's factory calibration services. Call Endevco's inside sales force at 800-982-6732 for recommended intervals, pricing and turn-around time for these services as well as for quotations on our standard products.
Continued product improvement necessitates that Endevco reserve the right to modify these specifications without notice. Endevco maintains a program of constant surveillance over all products to ensure a high level of reliability. This program includes attention to reliability factors during product design, the support of stringent Quality Control requirements, and compulsory corrective action procedures. These measures, together with conservative specifications have made the name Endevco synonymous with reliability. ENDEVCO CORPORATION, 30700 RANCHO VIEJO ROAD, SAN JUAN CAPISTRANO, CA 92675 USA (800) 982-6732 (949) 493-8181 fax (949) 661-7231 www.endevco.com Email:applications@endevco.com 0603 REV C

▲Up To Search▲

Price & Availability of 7596A

	To Download 7596A Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .